How To Clean A Bissell Pet Carpet Cleaner

Download Commodity

Download Article

Keep your Bissell carpet cleaner in good status by following the manufacturer's recommendations for cleaning it. Flush upright and portable machines after each use. Empty and rinse the dirty water tank after each utilise for upright and canister machines. Information technology's best to clean any parts of your vacuum you used for wet cleaning afterwards you're done using them. Rinse the filters for canister machines when they're visibly dirty.

1
Affluent the machine afterwards each use. Fill the water tank with hot water. Set the machine to loftier traffic and the handle to the recline position.^[1] Move the auto dorsum and forth on the carpet while pressing the spray trigger for fifteen seconds. Allow go of the trigger, then press it for another fifteen seconds while moving the machine back and along on the carpeting. Release the trigger a final time and vacuum without spraying until the car stops suctioning water.^[2]
- Flushing your machine with hot water after each use will remove any residuum solution which can harden in the spray lines.
- Once the carpet has stale, vacuum once more to articulate out dry debris like fuzz.^[3]
- Always make clean the machine before putting it in storage.^[four]
2

Wash out the hose. Suction make clean water from a basin or faucet to clean the hose. Once finished, lift the hose by the end. Stretch the hose to clear out the water.^[5]

Advertisement
3
Empty and rinse the tank. Turn off and unplug the motorcar, wrapping the ability string up deeply. Remove the tank and empty it into a sink. Rinse the tank with hot water. Make sure to rinse underneath and all effectually the bladder. Rinse away any debris from the red filter. Rinse the acme one-half of the tank through the nozzle area.^[6]
- If your model has more than one tank, remove and clean them both.^[7]
iv
Make clean the floor nozzle. With the h2o tank off the machine, remove the floor nozzle. Rinse the nozzle nether a faucet with hot water.^[8] Periodically make clean the fluid connection point with a small paperclip by removing the nozzle and turning it over.^[9] Supervene upon the nozzle by lining up the locking keys with the corresponding slots. Put the end caps and nozzle dorsum on the machine's foot. Turn the keys to lock it in place.
- Turn the locking keys to remove the floor nozzle.
five
Remove debris from the castor rolls. Pull or cut off any pilus or other debris. Turn the brush with your mitt to ensure that information technology spins freely (there should exist just minor resistance due to the motor). Depending on your model, y'all may need to remove screws to detach the brush gyre if you're unable to remove all debris otherwise.^[10]
- If you're unsure how to remove the brush coil, consult with your individual model's manual.
- Brush rollers can also be removed in some of the models like Bissell ProHeat 2X Revolution to clean the brushes in a better way, all y'all need is to remove the castor curlicue cover.^[11]
half-dozen

Clean the attachments. Separate whatever attachments from the machine. Rinse them under running h2o. Allow them to dry before replacing them on the hose rack.^[12]
vii
Clean the suction diverter. Take out the screws at the dorsum of the diverter'due south housing. Remove the diverter housing and rinse information technology under running water. Take out any droppings. Put the diverter housing back and secure it with the screws.^[13]
- Removing any droppings from the suction diverter prevents clogs from forming.
Advertisement

1

Rinse out the hose after each use. Fill up a bowl with clean water. Turn your machine on and suction the make clean water to rinse the interior of your machine.^[14] If your model has a hose, lift the hose up until whatever remaining h2o drains into the dirty water tank.^[15]
2
Rinse the dirty water tank after each use, or as needed. Plow the unit off by pressing the end push. Unplug and wrap up the ability cord. Lift off the muddy tank and empty it. Rinse the tank under running water, including the black valve inside the tank if your model has one.^[16]
- The tank will need to exist emptied and rinsed when it reaches the maximum make full line. Yet, for the all-time results, empty, rinse and dry all tanks earlier storing.^[17]
- If your model has a SpotBot automated characteristic, clean the brushing area and window with a soft cloth or microfiber towel.^[18]
- Information technology's condom to leave water and solution in the make clean tank unless you used Oxy Boost, in which case the tank volition demand be emptied and rinsed.
iii

Rinse the float stack, if applicable. Some models, such as the Trivial Green ProHeat 5207, have a float stack in the dirty tank. Remove this by turning information technology counter-clockwise. Rinse it with water before replacing it.
iv
Rinse the cleaning tool. Remove the cleaning tool from the spray trigger. Rinse the tool under running water. Clean dirt from the spray nozzle with a soft brush, if needed.^[19]
- Don't twist the cleaning tool; it should pull straight off subsequently yous push the lock button.
five

Make clean the suction gate, if applicative. Some portable machines, such as the SpotClean Pro 3624, accept a suction gate accessible once the dirty tank is removed. Unscrew the gate door.^[20] Wipe the gate clean and rinse information technology with h2o before replacing it.^[21]

Advertisement

ane
Empty and rinse the dirty water tank after each use. Plough off and unplug your machine. Empty the tank and rinse its bowl thoroughly. Wipe or air-dry the tank earlier replacing it.^[22]
- Remove the tank by opening the hose door and lifting the collection tank direct up past the handle. Take off the top hat.
ii
Remove and rinse any inner parts you used for moisture cleaning. Have out the h2o filtration tower, way selector, and/or hose. After rinsing them, let them dry out entirely before placing them dorsum into the auto.^[23]
- Remove the mode selector by turning it, then pulling it towards you. Remove the water filtration tower through the top tank.
iii
Rinse the filters as needed. Bank check the filters to see if they're visible muddied. When they are, rinse them with water. Permit them dry out completely earlier replacing them in your machine.^[24]
- Check the pre-motor filter by opening the top lid and pulling the tab. Make sure the "T" parts are lined up under their respective grooves when replacing the filter.
- Check the filter at the back of the machine below the cord wrap. Press the latch to pull the door down. Open up the door straight out and downwards. Remove the filter with two easily. Make sure the filter door is properly shut after replacing the filter.
Advertisement

Add together New Question

Question

Why is a microfiber towel suitable for cleaning?

Ashley Matuska is the possessor and founder of Dashing Maids, a sustainably focused cleaning bureau in Denver, Colorado. She has worked in the cleaning manufacture for over 5 years.

Professional person Cleaner

Skillful Answer

A microfiber towel picks up grit and removes it instead of spreading information technology around. It is reusable. You can wash it again and once again. It works well on types of surfaces.
Question

What can I use to clean grease?

Ashley Matuska is the owner and founder of Dashing Maids, a sustainably focused cleaning bureau in Denver, Colorado. She has worked in the cleaning manufacture for over v years.

Professional Cleaner

Expert Answer

Yous can use Citra Solv to clean grease. It is natural, smells expert, and works very well.

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Wipe the outside of your machine with a soft material as needed.^[25]
Use hot tap water, never boiled or microwaved water.^[26]

Plow the machine off and unplug information technology from any power source earlier you perform maintenance.^[27]

About This Article

Article Summary Ten

Cleaning your Bissell carpet cleaner regularly volition help continue information technology running smoothly. To clean an upright auto, you'll need to flush the car after each utilize with hot water. You'll also need to wash out the hose, empty and rinse the tank, and make clean the floor nozzle. Every few uses, remove debris from the castor rolls and apply scissors to cut away any hair that's trapped in it. To clean a portable automobile, remove the bladder stack and rinse it with water. You'll also want to rinse out the cleaning tool, and the suction gate. To learn how to clean a canister machine, read on!

Did this summary help you?

Thanks to all authors for creating a folio that has been read 66,887 times.